Mitsubishi Touch Screen concept Mitsubishi touch screen, also known as "Mitsubishi Human Machine Interface", is one of the well-known touch screen brands developed, produced and sold by Mitsubishi Electric Corporation. It is an inductive liquid crystal display device that can receive input signals such as contacts. When the graphic button on the screen is touched, the on-screen tactile feedback system can drive various connecting devices according to a pre-programmed program, which can be used instead of mechanical type. The button panel is made up of a liquid crystal display screen to create a live sound and video effect. At present, it has been widely used in machinery, textile, electrical, packaging, chemical and Other industries.
Mitsubishi touch screen works The Mitsubishi touch screen is controlled by pressure sensing. The main part of the Mitsubishi touch screen is a resistive film screen that is very compatible with the surface of the display. It is a multi-layer composite film with a layer of glass or hard plastic as the base layer and a transparent oxidized metal on the surface (transparent conductive). Resistor) Conductive layer, covered with a layer of outer surface hardened, smooth anti-scratch plastic layer, coated with a coating on its inner surface, with many fine (less than 1/1000 inch) transparency between them The isolation point separates the two conductive layers from each other. When the finger touches the screen, the two conductive layers have contact at the touch point position, the resistance changes, and signals are generated in both the X and Y directions, and then sent to the touch screen controller. The controller detects this contact and calculates the position of (X, Y), which then operates according to the way the mouse is simulated.
Mitsubishi touch screen input method Mitsubishi touch screen input letter mode:
The Mitsubishi touch screen has an automatic keyboard pop-up when using the touch screen value input, but the word keyboard can only be used to input numbers. If you want to enter letters, you must make a series of settings.
First, the user has to define a keyboard that can input letters, which can be set through the window screen of the touch screen, in which the user can set the letter to be input by using the key code switch. Secondly, the user should select the user-made window in the software, and the button window is set as the screen window of the homemade keyboard.
After setting the above, the user selects the ASCII input component in the touch screen and then downloads it to the touch screen. After connecting the normal communication of the plc, as long as the position of the ASCII input is pressed, the user-defined keyboard will pop up.
Mitsubishi touch screen classification Mitsubishi touch screen has the following series, namely Mitsubishi touch screen GT16 series, Mitsubishi touch screen GT15 series, Mitsubishi touch screen GT12 series, Mitsubishi touch screen GT11 series, Mitsubishi touch screen GT10 series, Mitsubishi touch screen GOT1000 series. Among them, the GOT1000 series has GOT1000 and is divided into two series: GT15 and GT11. The GT11 is a basic function model, while the GT15 is a high-performance model.
Mitsubishi touch screen model and price Mitsubishi touch screen GT1685M-STBD: 9500 yuan
Mitsubishi man-machine interface GT2310-VTBA: 5400 yuan
Mitsubishi touch screen GT1675-VNBD: 8600 yuan
Mitsubishi 10 inch man-machine interface GS2110-WTBD: 3300 yuan
Mitsubishi man-machine interface GT1055-QSBD-C: 2500 yuan
Mitsubishi MITSUBISHI touch screen GT1155HS-QSBD: 7300 yuan
Mitsubishi touch screen GT2308-VTBA: 8,000 yuan
Mitsubishi man-machine interface touch screen GT2510-VTBA: 9900 yuan
Mitsubishi touch screen GT2712-STBA: 39000 yuan
Mitsubishi touch screen model selection skills 1. GT1155-QSBD can not completely replace GT1155-QSBD, the difference is that the "Q" in GT1155-QSBDQ means the built-in Q bus connection module. If the customer does not use the Q bus connection module, it can be replaced with GT1155-QSBD.
2. GT1155-QSBDA can not completely replace GT1155-QSBD The difference between "A" in GT1155-QSBDA is that it has its own A bus connection module. If the customer does not use the A bus connection module, it can be replaced with GT1155-QSBD.
3. GT2308-VNBA does not support BUS bus, GT23 does not support BUS bus, GT27 support.
4. Q: Please refer to the following figure for the definition of GT1000 series models.
5. Q: The GT1695M-XTBA and GT1695M-XTBD input power supply are different. The GT1695M-XTBA is AC220V, the GT1695M-XTBD is DC24V, and the others are exactly the same.
6. Mitsubishi touch screen editing program software uses GTWorks3 software
7. GT1055-QSBD-C and GT1055-QSBD are both produced in Japan; -C is for the Chinese market, China sales meaning, the difference between the two GT1055-QSBD has a battery; and -C does not have a battery, such as customers A battery is required for battery-related functions, model GT11-50BAT.
8. What are the specific differences between the GT1020 models? See the table below, where the power supply voltage is DC5V and can be directly powered by the communication line.
9. GT1665HS-QTBD is a hand-held touch screen with a special 42-pin interface. It needs to be converted into a common interface for normal use.
The basic accessories are: GT16H-C30-42P (3m extension cable) + GT16H-CNB-42S (connection conversion box)
1) Connection with FXplc requires additional communication line: GT01-C30R4-8P (all accessories: GT16H-C30-42P+GT16H-CNB-42S+GT01-C30R4-8P)
2) Connection with QPLC requires additional communication line: GT01-C30R2-6P (all accessories: GT16H-C30-42P+GT16H-CNB-42S+GT01-C30R2-6P)
10. Q: The accessories and communication lines required for the GT1155HS-QSBD/GT1150HS-QLBD handheld touch screen and FX or QPLC connection are:
1) Connection with FX 1: GT11H-C30-37P (3m extension cable) + GT11H-CNB-37S (connection conversion box) + GT01-C30R4-8P (FX communication line)
2) Connection with FX 2: GT11H-C30-37P (3m extension cable) + GT11H-C15R4-8P (1.5m conversion FX communication line)
3) and Q connection mode 1: GT11H-C30-37P (3 m extension cable) + GT11H-CNB-37S (connection conversion box) + GT01-C30R2-6P (Q communication line)
4) and Q connection mode 2: GT11H-C30-37P (3 m extension cable) + GT11H-C15R2-6P (1.5 m conversion Q communication line)
Can GT15-MESB48M be used instead of GT15-QFNB48BM?
This depends on the specific use;
If it is the memory expansion/multi-channel function/document display function/ladder monitoring function/SFC monitoring function/ladder editing function for the GT15 screen, the two functions can be replaced by each other;
If it is used for MES interface function expansion, you must use GT15-MESB48M, you can not use GT15-QFNB48BM instead.
Mitsubishi touch screen use precautions 1. The surface of the Mitsubishi touch screen is the touch surface, which is the front of the product; the glass surface is the non-touch surface, that is, the back of the product.
2, Mitsubishi touch screen part is glass products, glass corners are sharper, please wear gloves / finger sets when assembling.
3, Mitsubishi touch screen part is glass fragile, do not exert a strong impact on the touch screen when assembling.
4. Avoid taking the lead directly and pick up the touch screen to avoid pulling the lead wire.
5. The bending line of the lead wire reinforcement plate cannot be bent.
6. No folding is allowed in any part of the lead wire. 7. When the lead wire is assembled, it must be inserted horizontally. Do not insert it at the root of the reinforcing plate.
8. When handling the product, it needs to be handled by a single piece. Handle it gently to avoid the product colliding with each other and scratching the surface of the product.
9. When cleaning the surface of the product, wipe it with a soft cloth (deer skin) and petroleum ether.
10. Do not wipe the surface of the touch screen film with a corrosive organic solvent. Such as industrial alcohol.
11, do not stack the touch screen, use the tray.
12. In the assembly design and frame design, please pay attention to the following items:
1) The pillars of the frame of the fixed Mitsubishi touch screen shall be outside the visible area of the touch screen;
2) The frame edge shall be outside the operation area of the Mitsubishi touch screen, and the frame side shall not have pressure action in the visible area to the operation section;
3) It is recommended that the material of the fixed Mitsubishi touch screen be a plastic material, and the front part of the touch screen is padded with a soft material;
4) Do not stick the corrosive adhesive to the surface of the touch screen.
